You need gcc version 2.0 or later to compile gforth.
configure has the following useful parameters:
--prefix=PREFIX install architecture-independent files in PREFIX
--exec-prefix=PREFIX install architecture-dependent files in PREFIX
[default: same as prefix]
--enable-force-reg Use explicit register declarations if they appear in
the machine.h file. This can cause a good speedup,
but also incorrect code with some gcc versions on
some processors (default disabled).
--enable-direct-threaded Force direct threading. This may not work on
some machines and may cause slowdown on others.
--enable-indirect-threaded Force indirect threading. This can cause a
slowdown on some machines.
--with-debug specifies option -g to compile with debug info (default)
--without-debug omits the -g switch and creates smaller images on
machines where strip has problems with gcc style
--help: tells you about other parameters.
If you don't like the defaults for the installation directories, you
should override them already during configure. E.g., if you want to
install in the /gnu hierarchy instead of in the default /usr/local
Moreover, if your GCC is not called gcc (but, e.g., gcc-2.7.1), you
should say so during configuration. E.g.:
env CC=gcc-2.7.1 ./configure
You can also pass additional options to gcc in this way, e.g., if you
want to generate an a.out executable under Linux with gcc-2.7.0:
env "CC=gcc -b i486-linuxaout -V 2.7.0" ./configure
After, configuration, type
Now you can check whether your shiny new Forth system works. Say
You can run some benchmarks with
and compare them with the results in Benchres and in the manual.
If everything is all right, you may want to install gforth. Type
You have to make an entry in the info directory file manually.
For paper documentation, print gforth.ps (a Postscript file (300dpi
fonts, i.e., it works, but does not produce best quality on better
printers)), or say
and print the resulting file gforth.dvi. You can also get the
documentation in HTML format by typing
If you prefer plain ASCII documentation, just concatenate the files
gforth.info-* ('cat gforth.info-*' under Unix).
Preloading installation-specific code
If you want to have some installation-specific files loaded when
Gforth starts (e.g., an assembler for your processor), put commands
for loading them into /usr/local/share/gforth/site-forth/site-init.fs
(if the commands work for all architectures) or
/usr/local/lib/gforth/site-forth/site-init.fs takes precedence if both
files are present (unless you change the search path). The file names
given above are the defaults; if you have changed the prefix, you have
to replace "/usr/local" in these names with your prefix.
By default, the installation procedure creates an empty
/usr/local/share/gforth/site-forth/site-init.fs if there is no such
If you change the site-init.fs file, you should run "make install"
again for the changes to take effect (Actually, the part of "make
install" starting with "rm gforth.fi" is sufficient).
Multiple Versions and Deinstallation
Several versions of Gforth can be installed and used at the same
time. Version `foo' can be invoked with `gforth-foo'. We recommend to
keep the old version for some time after a new one has been installed.
You can deinstall this version of Gforth with 'make uninstall' and
version foo with 'make uninstall VERSION=foo'. 'make uninstall' also
tells you how to uninstall Gforth completely.
A Possible Problem
You need to read this only if you see a message like
The Gforth installer should look into the INSTALL file
1) "gforth: Cannot load nonrelocatable image (compiled for address $1234) at address $5678
The Gforth installer should look into the INSTALL file"
Gforth supports both relocatable and fixed-address images. If you load
normal Forth code and save the image, you get a fixed-address
image. Producing a relocatable image is more difficult.
Therefore, Gforth has only a relocatable image of the kernel
(kernel.fi), which is powerful enough to load the rest of
Gforth. However, loading the rest takes a noticable amount of time. To
avoid this delay (which would occur on every startup), the
installation procedure produces an image fixed at an address
determined at the Gforth run that produced the image. This
fixed-address image is loaded by default. On most OSs this works,
because the first chunk of memory is always allocated at the same
address. If the address changes, you get the message above.
An image address change can be caused by a change of the gforth
executable, or by a change (upgrade) of the OS; in these cases you
just have to rebuild and reinstall the fixed address image with
rm gforth.fi; make gforth.fi; make install
If you get such a message with a different address in place of the
$5678 each time you try to start gforth, you cannot use fixed-address
images on your OS. In this case, send us a message so that we start
searching for a comfortable solution to this problem. In the
meantime, start gforth with
gforth -i kernel.fi startup.fs
2) "%s: Checksum of image ($13579b) does not match the executable ($2468a)
The Gforth installer should look into the INSTALL file"
A fixed-address image is not only fixed with respect to its base
address, but also with respect to certain addresses in the gforth
executable and the threading method. These things are encoded in a
If the checksum of the executable and the checksum of the image are
not equal, you get the message above. This can be caused, e.g., by
trying to run an image produced for a direct threading system on an
indirect threaded system.
Chances are that you unintentionally tried to execute an image from
the wrong directory. As a remedy, you can determine Gforth's search
path with the "-p" command line option and with the GFORTHPATH
On the other hand, if you need to solve the problem by creating a new
fixed-address image, you can use the steps described above.